Product categories
More »
Stainless Steel
Stainless Steel specifications held in the austenitic, martensitic and precipitation hardening varieties. Stocks are held in British Standard and International standards. Below is listed our most commonly supplied grades; please contact our sales office. Also stock is 301 stainless spring temper rolled strip.
Hi-Steel HSLA-80
Hi - Speed, high Speed Steel Tool Steel (made) : highly processed into the Tool Steel, carbon content high, while containing cr quantity is low (about 4%), reason burnish of Steel surface gloss darker, after heat can reach by HRc62 high hardness, resistance to rust performance not on a roll.
Mould Steel
Steel mould and Steel mould suppliers, global delivery, stock supply Steel mould steels.
Heat Resistant Steel
Heat resistant steel. AS Orlov Izobret. Mashinostr. 3, 48-49, 7/2000. The purpose of this work was to increase plasticity of heat resistant steel after aging at the 500-1300 deg C temperature and to improve its operational reliability.
Tool Steel
Comprehensive stocks held of tool steel, including hot work, cold work and plastic mould tool steel specifications. Below we detail our most common grades. Other British Standard and international special steels and tool steels are also available, please contact our sales office.
Ball Bearing Steel
Supplies Ball bearing steel of all types, along with carbon steel and specialty balls, to OEM's around the world. Also offers platinum balls, brass balls, gold, titanium, aluminum, carbon and plastic balls.
Spring Steel
Carbon spring steel is held in a wide range of sizes. Detailed below are our most common specifications. Carbon steel strip and spring steel sheet is available most commonly in the hardened and tempered condition, though certain sizes are available in the annealed condition. Round and flat bar is stocked in the as rolled condition. Most spring steel specifications are held to British Standard steel specifications including BS1449 & BS970.
Alloy and Carbon Steel
Alloy steel is steel alloyed with a variety of elements in total amounts of between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is somewhat arbitrary: Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0 %.[1][2] Most commonly, the phrase "alloy steel" refers to "low alloy" steels.
News
More »
Enterprise email
Home » Tool Steel » Product introduction
AISI 4150 Tool Steel
- Numbers: 2011030513
- Model: AISI 4150
- Producers: China
- Update time: 2011.03.05
- Browse:
Product Description:
Tool Steel
AISI 4150 Tool Steel
- HOT ROLL FINISH
- HOT ROLL T & B WITH SAW-CUT EDGES
DESCRIPTION
A special analysis of Alloy steel which is heat treated by oil-quenching and tempering to develop a balance of mechanical properties. Has every requisite for brake die service-high wear-resistance, adequate toughness, high resistance to impact, and good machinability. In addition, the bars are stress-relieved before the final gag straightening, to insure a minimum of residual stresses.
TYPICAL ANNALYSIS
CARBON ……0.51 MANGANES ………0.87
CHROMIUM …0.95 MOLYBDENUM ……0.20
ADVANTAGES
-
Heat treated, ready to use, needs no further hardening
-
Heat treated to the right hardness for maximum wear and toughness
-
Machines easily without warping-due to strain-relief treatment
-
Machines to a smooth surface without grinding
-
Hardened to between 248-293 Brinell – the correct hardness for most uses
-
High carbon content insures greater resistance to wear
-
Small areas can be flame hardened for better wear.
DISTORTIONAL PROPERTIES
As free from residual stresses as possible due to the method of heat treating. Machining an equal amount evenly from each side of the brake die will result in minimum deformation and warping.
COMPRESSIVE STRENGTH
To obtain values for this property, specimens were taken from large and small sections, machined oversize, heat treated and finished by grinding to 0.505 in. diameter x 0.750 in. long. The specimens were checked for hardness and were then compressed between hardened steel plates. the specimens tested showed a hardness of 269 Brinell and indicated that both small and large sections developed compressive strength in excess of 100,000 psi, adequate compressive strength to meet the maximum demand of heavy duty brake-die service.
Special Steel classification：
Stainless steel，Hi-Steel HSLA-80，Steel mould,Heat resistant steel,Tool Steel,Ball bearing
steel,Spring steel,Alloy steel,Construction steel，Die steel，Mould steel.
Product description：
Step Shaft AISI 4150 Tube AISI 4150 Pie-shaped AISI 4150 Ring AISI 4150 Module AISI 4150 Large
valves of the main AISI 4150 Other Profiled forgings AISI 4150
Products Introduction :
Specialized and high quality steel.
We have the advantages of equipment, technologies and price.
Specifications
Round bar ：
Diameter : 1mm-2000mm
Square bar:
Size： 50mm * 50mm-600mm *600mm
Plate steel/flat bar:
Size：Thickness:0.1mm-800mm Width:10mm to 1500mm
Tube/pipe:
Size：OD:6-219mm WT：1-35 mm.
Cold-rolled sheet:Thickness:2-5mm Width:1000mm Length:2000mm
Hot-rolled sheet:Thickness:6-80mm Width:210-610mm
Length: We can supply any length based on the customer's requirement.
Forging/hot rolling/ extrusion of steel.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching
+ tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on
the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable
electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the
customer's requirement
Excellent service for all kinds of industries,with advantages of technologies, equipment and
price.
We serve you with our honesty, integrity, and professionality.
